[INFO     Flash Code@26-03-26 15:56:30] Firmware File C:\Program Files\SmartSnippetsToolbox\SmartSnippetsToolbox5.0.26\common_resources\SupportPackages\DA1453x\toolbox_resources/common/flash_programmer_535.bin has been selected for downloading.
[INFO     Flash Code@26-03-26 15:56:30] Connection to COM13 port has successfully opened.
[INFO     Flash Code@26-03-26 15:56:30] Started download procedure...
[ACTION   Flash Code@26-03-26 15:56:31] Please press the hardware reset button on the board to start the download process.
[ERROR    Flash Code@26-03-26 15:56:38] Timeout: Reset signal not detected for more than 8000 msecs.
[INFO     Flash Code@26-03-26 15:56:38] Please try again. If problem persists refer to User Manual AN-B-072 (AN-B-072: DA1453x Booting from OTP and Serial Interfaces) and check jumper settings. For booting from 2-wire UART  (P0_0 and P0_1) see Figure 10. For booting from 1-wire UART P0_5 see Figure 6.
[ERROR    Flash Code@26-03-26 15:56:38] Error while writing to the board.
[INFO     Booter@26-03-26 15:56:38] Successfully disconnected from port COM13.
[ERROR    Booter@26-03-26 15:56:38] Failed to close COM13
[ERROR    Flash Code@26-03-26 15:56:38] Failed downloading firmware file to the board.
[INFO     Flash Code@26-03-26 15:56:55] Firmware File C:\Program Files\SmartSnippetsToolbox\SmartSnippetsToolbox5.0.26\common_resources\SupportPackages\DA1453x\toolbox_resources/common/flash_programmer_535.bin has been selected for downloading.
[INFO     Flash Code@26-03-26 15:56:55] Connection to COM13 port has successfully opened.
[INFO     Flash Code@26-03-26 15:56:55] Started download procedure...
[ACTION   Flash Code@26-03-26 15:56:56] Please press the hardware reset button on the board to start the download process.
[INFO     Flash Code@26-03-26 15:57:00] Reset detected
[INFO     Booter@26-03-26 15:57:00] Successfully disconnected from port COM13.
[INFO     General@26-03-26 15:57:01] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:57:01] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:57:01] Detected flash with the following properties: manufacturer: Macronix, name: MX25R2035F, jedec id: 0xC22812, size: 262144 bytes.
[INFO     SPI Flash Programmer@26-03-26 15:57:25] Copying file: F:\Project\TPMS\empty_peripheral_template_535 1.bin to C:\Users\ELPIS_~1\AppData\Local\Temp\\input1.bin.
[WARNING  OTP Image@26-03-26 15:57:25] 4 0xFF bytes added at the end of read data for padding.
[INFO     Flash Code@26-03-26 15:57:25] Read 27300 bytes from file C:\Users\ELPIS_~1\AppData\Local\Temp\\input1.bin.
[INFO     Flash Code@26-03-26 15:57:28] Started reading 32768 bytes from memory.
[INFO     SPI Flash Programmer@26-03-26 15:57:28] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:57:28] Successfully disconnected from port COM13.
[INFO     SPI Flash Programmer@26-03-26 15:57:28] Successfully configured SPI ports and pins.
[INFO     Flash Code@26-03-26 15:57:28] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:57:30] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:57:30] Read 16384 bytes from offset 0x00
[INFO     Flash Code@26-03-26 15:57:30] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:57:31] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:57:31] Read 16384 bytes from offset 0x4000
[INFO     Flash Code@26-03-26 15:57:31] Reading has finished. Read 32768 bytes.
[INFO     SPI Flash Programmer@26-03-26 15:57:46] Copying file: F:\Project\TPMS\empty_peripheral_template_535 1.bin to C:\Users\ELPIS_~1\AppData\Local\Temp\\input1.bin.
[WARNING  OTP Image@26-03-26 15:57:46] 4 0xFF bytes added at the end of read data for padding.
[INFO     Flash Code@26-03-26 15:57:46] Read 27300 bytes from file C:\Users\ELPIS_~1\AppData\Local\Temp\\input1.bin.
[INFO     Flash Code@26-03-26 15:57:53] Check if memory empty...
[INFO     Flash Code@26-03-26 15:57:53] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:57:54] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:57:54] Read 16384 bytes from offset 0x00
[INFO     Flash Code@26-03-26 15:57:54] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:57:56] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:57:56] Read 10916 bytes from offset 0x4000
[INFO     SPI Flash Programmer@26-03-26 15:57:58] Started erasing from 0x00 to 0x7000 (8 sectors)
[INFO     SPI Flash Programmer@26-03-26 15:57:58] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:57:58] Successfully disconnected from port COM13.
[INFO     SPI Flash Programmer@26-03-26 15:57:58] Memory erasing completed successfully.
[INFO     Flash Code@26-03-26 15:57:59] Started burning memory with 27300 bytes of data at address 0x00.
[INFO     SPI Flash Programmer@26-03-26 15:57:59] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:58:01] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:58:01] Burned chunk with size 16384 bytes at offset 0x00
[INFO     SPI Flash Programmer@26-03-26 15:58:01] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:58:02] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:58:02] Memory burning completed successfully.
[INFO     Flash Code@26-03-26 15:58:02] Reading memory to refresh table contents....
[INFO     Flash Code@26-03-26 15:58:02] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:58:04] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:58:04] Read 16384 bytes from offset 0x00
[INFO     Flash Code@26-03-26 15:58:04] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:58:05] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:58:05] Read 10916 bytes from offset 0x4000
[INFO     Flash Code@26-03-26 15:58:05] Reading has finished. Read 27300 bytes.
[INFO     General@26-03-26 15:58:05] Connection to COM13 port has successfully opened.
[INFO     Booter@26-03-26 15:58:05] Successfully disconnected from port COM13.
[INFO     Flash Code@26-03-26 15:58:05] Successfully sent reset command. If application won't start replug the board.
